6861AAQ IC Schematic Circuit Diagram Pinout Substitute and Datasheet

IC Number- 6861AAQ, Pins- 48, Pakege type - 7mm x 7mm, QFN (Quad Flat No-Lead), Application- TFT LCD TV Panel Power Management.

6861AAQ IC Circuit Diagram Pinout Substitute & Datasheet.

To supply the bias voltages of millions of transistors inside the TFT LCD display of LCD TV, Inside the 6861AAQ IC, there are several low-dropout voltage regulators, which regulators are controlled by high-speed and high-precision voltage amplifiers.

The input voltage (VIN) or operating voltage of 6861AAQ IC is DC 8 volts to 14 volts. 6861AAQ IC has a switching circuit inside the IC for voltage boost, which has fixed switching frequencies of 500 kHz and 750 kHz, depending on the circuit design.
6861AAQ IC has a 150mA charge pump driver circuit for the adjustable VGL Output voltage. A 150mA current limit positive charge pump driver circuit is also used for adjustable VGH Output voltage. In the LCD TV power management circuit made by 6861AAQ IC, I observed that the maximum output voltage is 30 volts as VGH.
The DC-to-DC converter circuits of the 6861AAQ IC are characterized by an adjustable soft start, adjustable current limit, and thermal shutdown; the temperature range of this IC is -40 °C to +85°C.

6861AAQ IC Schematic Circuit Diagram Pinout Substitute and PDF Datasheet

 • VGH =  30 Volts,  • VGL=  -8 Volts,  • AVDD= 15 Volts,  • VCOM=  8 Volts 

The VCOM voltage controls the signal current of the thin film transistors in the display to maximize the contrast of the LCD image. The 6861AAQ IC has a high-speed operational amplifier circuit to accomplish that process. Moreover, there is a high-speed and low-dropout reference voltage output circuit for the gamma buffer inside the 6168AAQ IC; high-current and high-accuracy operational amplifiers are used there.
[ CM501 IC Schematic Circuit Diagram? Click Here ]

Instead of the 6861AAQ IC PDF datasheet-

6861AAQ IC Pinout & Pins Function

1. Reference voltage (From AVDD) input terminal of the internal linear regulator.
2. VOP- Voltage input terminal of internal Operational Amplifier.
3. GND- Ground of operational amplifier
4. OPP- Noninverting input of the operational amplifier (Internal)
5. OPN- Inverting input of the operational amplifier (Internal)
6. OPP- Output of Opamp (VCOM output)
7. XAO- XAO signal output of reset function. The XAO signal detects the screen disappearance.
8. GVOFF- High voltage switching terminal controlled by T-Con.
9. EN - Enable the VGH charge pump.
10. FB2- Feedback-2: Feedback from the buck converter Output is provided here.
11. Out- The output sense of the buck converter is input here.
12. GND - This is the ground of the buck converter output section.
13. LX2- This is the Source terminal of the buck converter Output MOSFET (Internal).
14. LX2- It is also the source terminal of the buck converter output MOSFET.
15. BST - Bootstrap- The Internal Supply terminal of the high-side MOSFET gate driver.
16. In-2, the operating voltage (VIN) is inputted here.
17. In-2, This is also the VIN
18. GND- Main GND for 6861AA or #LP6283 IC
19. VDET
20. INVL- Supply voltage is applied to the internal 4-volt regulator circuit.
21. VL- VL terminal
22. FSEL - Frequency Selection, High or Low-Frequency Selection Terminal.
23. CLIM – Current Limit, To protect over-current.
24. SS- For soft start, tolerate voltage output.

25,26. SW - Amplified switching voltage output for AVDD
27,28 - Power ground terminal of the boost regulator circuit
29. GD_I - This terminal acts as an output sense to detect overvoltage.
30. Get the Driver of the AVDD regulator MOSFET.
31. FB- Feedback for smooth AVDD output
32. COMP- Compensation pin of boost voltage regulator error amplifier
33. THR (not used)
34. SUPP - Supply, The internal power supply of the VGH charge pump circuit.
35. CPGND- Ground of Charge pump circuit
36. DRVP- The output terminal of the VGH charge pump driver circuit.
37. DLY1
38. FBP- VGH feedback
39. VGH- Get voltage high
40. VGHM- Externally Not used in this 6861AAQ circuit
41. NC
42. SUPN is the internal power supply pin of the VGL charge pump circuit.
43. DRVN- VGL Output terminal
44. GND- Ground of VGL charge pump circuit
45. FBN- Feedback of VGL
46. REF- Reference
47. VREF_FB - Feedback of input
48. VREF_0

Sony Bravia Smart TV Red Light Blinking 2-Times? Click Here.

Tips for LED TV repair technicians-

If a short circuit occurs in the 6861AAQ DC-to-DC converter circuit, or if a Short Circuit from VIN to the ground is found when measured with a meter, check the D11 diode, C27, C28, and C29 located on the schematic circuit diagram because if you look at the circuit diagram, you will understand that these components are directly connected from VIN to the ground.

Substitute of 6861AAQ IC

Substitutes for 6861AAQ IC can be RT9955 and 5562A, as the circuit of these three ICs is almost the same. I will publish the correct information here after I am sure about this.
#5562A
#6861AAQ
#RT9955
Good luck, everyone. Thanks.